{"product_id":"pololu-15v-step-up-voltage-regulator-u3v70f15","title":"Pololu 15V Step-Up Voltage Regulator U3V70F15","description":"\u003cp\u003eThe U3V70x boost (step-up) voltage regulators are high-current, high-efficiency synchronous switching regulators that \u003cstrong\u003egenerate higher output voltages from input voltages\u003c\/strong\u003e as low as 2.9V - this particular model (\u003cstrong\u003eU3V70F15\u003c\/strong\u003e) provides a \u003cstrong\u003e15V output voltage\u003c\/strong\u003e with a \u003cstrong\u003eminimum input voltage of 2.9V\u003c\/strong\u003e (typical \u003cstrong\u003emax input current* 7A\u003c\/strong\u003e).\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e* Actual achievable continuous current is a function of input voltage and is limited by thermal dissipation. See the output current graphs on the product pages for more information.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003eThe regulators actively limit the instantaneous input currents to \u003cstrong\u003e10A\u003c\/strong\u003e, and the input current can typically be as high as \u003cstrong\u003e8A\u003c\/strong\u003e for several seconds before the thermal protection activates. Input currents of around \u003cstrong\u003e6A\u003c\/strong\u003e can typically be maintained for many minutes without triggering thermal shutdown, though the actual performance depends on the input and output voltages as well as external factors such as ambient temperature and airflow.\u003c\/p\u003e\n\u003cp\u003eFor boost regulators, the output current equals the input current times the efficiency times the ratio of VIN to VOUT, so the more you are boosting, the lower the maximum output current will be (see the Typical efficiencies and output currents section below for performance graphs).\u003c\/p\u003e\n\u003cp\u003eThese regulators feature a variety of built-in protections, including reverse voltage protection to keep your load safe in the event power is accidentally connected backwards, and unlike most boost regulators, these units offer a true shutdown option that turns off power to the load (with typical boost regulators, the input voltage will pass directly through to the output when they are disabled).\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWarning: During normal operation, this product can get hot enough to burn you.\u003c\/strong\u003e Take care when handling this product or other components connected to it.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput voltage: 2.9V\u003c\/strong\u003e to \u003cstrong\u003e15V\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOutput voltage: 15V with 4% accuracy\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003eTrue shutdown option turns off power to the load\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTypical efficiency of 80% to 95%\u003c\/strong\u003e, depending on input voltage, output voltage, and load (see the Typical efficiencies and output currents section below for performance graphs)\u003c\/li\u003e\n\u003cli\u003e10A switch allows for:\n\u003cul\u003e\n\u003cli\u003eInstantaneous input currents up to \u003cstrong\u003e10A\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eInput currents up to \u003cstrong\u003e7A\u003c\/strong\u003e for several seconds\u003c\/li\u003e\n\u003cli\u003eInput currents around \u003cstrong\u003e6A\u003c\/strong\u003e for prolonged durations\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003elow quiescent current for input voltages over 3.5 V (see the quiescent current graph below for more details)\u003c\/li\u003e\n\u003cli\u003eIntegrated protections:\n\u003cul\u003e\n\u003cli\u003eReverse voltage protection\u003c\/li\u003e\n\u003cli\u003eShort-circuit protection with hiccup recovery\u003c\/li\u003e\n\u003cli\u003eOver-temperature shutoff\u003c\/li\u003e\n\u003cli\u003eUnder-voltage lockout (typical thresholds are 2.4 V falling, 2.8 V rising)\u003c\/li\u003e\n\u003cli\u003eCycle-by-cycle input current limiting to 10 A\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eCompact size: 1.6″ × 0.6″ × 0.18″ (40.6 × 15.2 × 4.6 mm)\u003c\/li\u003e\n\u003cli\u003eWeight: 3.5 g\u003c\/li\u003e\n\u003cli\u003eTwo mounting holes for #2 or M2 screws\u003c\/li\u003e\n\u003cli\u003eSmaller holes for 0.1″ header pins and larger holes for terminal blocks offer several options for connecting to the board\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eMinimum operating voltage: \u003cstrong\u003e2.9V\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum operating voltage: \u003cstrong\u003e15V\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum input current: \u003cstrong\u003e10A\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eOutput voltage: \u003cstrong\u003e15V\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eReverse voltage protection?: Y\u003c\/li\u003e\n\u003cli\u003eOutput type: \u003cstrong\u003eFixed 15V\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eSize: 0.6″ × 1.6″ × 0.18″\u003c\/li\u003e\n\u003cli\u003eWeight: 3.6g\u003c\/li\u003e\n\u003cli\u003ePCB dev codes: reg21a\u003c\/li\u003e\n\u003cli\u003eOther PCB markings: 0J11050, blank white box\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eUsing the U3V70F15\u003c\/h2\u003e\n\u003ch3\u003eConnections\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/U3V70F15_pinout.jpg?v=1713969606\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003eThe input voltage, \u003cstrong\u003eVIN\u003c\/strong\u003e, must be \u003cstrong\u003eat least 2.9V\u003c\/strong\u003e and should not exceed the output voltage, \u003cstrong\u003eVOUT\u003c\/strong\u003e. (If VIN is higher than VOUT, the higher input voltage will show up on the output, which is potentially dangerous for your connected load and could also damage the regulator.)\u003c\/p\u003e\n\u003cp\u003eThe regulator is enabled by default: a 100 kΩ pull-up resistor on the board connects the \u003cstrong\u003eENABLE\u003c\/strong\u003e pin to reverse-protected VIN. The ENABLE pin can be driven low (under 0.4 V) to turn off power to the load and put the board into a low-power state. The typical no-load quiescent current is less than 1 mA (see the quiescent current graph below for more details).\u003c\/p\u003e\n\u003ch3\u003eTypical efficiencies and maximum output currents\u003c\/h3\u003e\n\u003cp\u003eThe efficiency of a voltage regulator, defined as (Power out)\/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. As shown in the graphs below, the U3V70x regulators have an efficiency of 80% to 95% for most combinations of input voltage, output voltage, and load.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/U3V70A_5v.png?v=1713368431\"\u003e5V graph\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/U3V70A_7.5v.png?v=1713368431\"\u003e7.5V graph\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/U3V70A_9v.png?v=1713368431\"\u003e9V graph\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/U3V70A_12v.png?v=1713368432\"\u003e12V graph\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/U3V70A_15v.png?v=1713368431\"\u003e15V graph\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe maximum achievable output current is approximately proportional to the ratio of the input voltage to the output voltage. Additionally, the maximum output current can depend on other factors, including the ambient temperature, airflow, and heat sinking. The graph below shows the typical maximum continuous output currents these regulators can deliver at room temperature with no forced airflow or heat sinking.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/U3V70A_output_current.jpg?v=1713435295\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWarning: During normal operation, this product can get hot enough to burn you.\u003c\/strong\u003e Take care when handling this product or other components connected to it.\u003c\/p\u003e\n\u003ch3\u003eLC Voltage Spikes\u003c\/h3\u003e\n\u003cp\u003eWhen connecting voltage to electronic circuits, the initial rush of current can cause damaging voltage spikes that are much higher than the input voltage. In our tests with this family of regulator connected with typical power leads (~30″ test clips), we found that input voltages above 17V caused voltage spikes in excess of 20V, which could damage the regulator.\u003c\/p\u003e\n\u003cp\u003eLower input voltages caused smaller spikes that could still be problematic for boost regulators operating with the input voltage close to the set output voltage, since input voltages above the set output voltage will propagate to the output and could damage circuits being powered by the regulator. A large electrolytic capacitor (33 μF is a good starting point) can be added close to the regulator between VIN and GND to help suppress these spikes.\u003c\/p\u003e\n\u003cp\u003eMore information about LC spikes can be found in our application note, \u003ca href=\"https:\/\/www.pololu.com\/docs\/0J16\"\u003eUnderstanding Destructive LC Voltage Spikes\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eResources\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.pololu.com\/file\/0J1560\/step-up-voltage-regulator-u3v70x-dimensions.pdf\"\u003eDimensions\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.pololu.com\/file\/0J1561\/step-up-voltage-regulator-u3v70x.step\"\u003e3D Model\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.pololu.com\/file\/0J1559\/reg21a-drill.dxf\"\u003eDrill guide\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003ePackage Contents\u003c\/h2\u003e\n\u003cp\u003eAlong with the regulator, you will receive a 9-way 0.1\" header strip and two terminal blocks.\u003c\/p\u003e\n\u003cp\u003eThis regulator offers several options for making electrical connections. The nine smaller through-holes on the ends of the board are arranged with a 0.1″ spacing for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. The included 0.1″ male header can be broken or cut into smaller pieces as desired and soldered into these smaller through-holes.\u003c\/p\u003e\n\u003cp\u003eAlternatively, the included terminal blocks can be soldered into the larger holes to allow for convenient temporary connections of unterminated wires (\u003ca href=\"https:\/\/www.youtube.com\/watch?v=6pDyTLRZ2Eg\"\u003esee our short video on terminal block installation\u003c\/a\u003e). You can also solder wires directly to the board for the most compact installation.\u003c\/p\u003e","brand":"Pololu","offers":[{"title":"Default Title","offer_id":50847392858385,"sku":"POL-2896","price":17.3,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0901\/6285\/6209\/files\/pololu-15v-step-up-voltage-regulator-u3v70f15-pololu-pol-2896-42046160961731.jpg?v=1735212409","url":"https:\/\/abcd3032.myshopify.com\/nl\/products\/pololu-15v-step-up-voltage-regulator-u3v70f15","provider":"Tayyab Zak","version":"1.0","type":"link"}