{"product_id":"power-bank-keepalive-assembled","title":"Power Bank KeepAlive (Assembled)","description":"\u003cp\u003eThis product is identical to our popular \u003ca href=\"\/ru\/products\/power-bank-keep-alive-based-on-555-timer-kit-form\"\u003eKeepAlive Kit\u003c\/a\u003e but comes pre-assembled using SMD components, making it easier and more compact!\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eMost power banks will automatically turn off their USB ports when the power\/current being drawn is lower than a certain value. This makes it impossible to run low-power devices on a power bank, such as a \u003ca href=\"\/ru\/collections\/pico\"\u003eRaspberry Pi Pico\u003c\/a\u003e, small \u003ca href=\"\/ru\/collections\/adafruit-development-boards\"\u003emicrocontrollers\u003c\/a\u003e or even charge your AirPods.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e...until now!\u003c\/strong\u003e This is a \u003cstrong\u003eUSB KeepAlive (assembled SMD version)\u003c\/strong\u003e which does exactly that - it keeps your power bank 'alive' by pulsing a small amount of current (via a 555 timer - \u003cem\u003eneat\u003c\/em\u003e) through the USB port. The pulse combined with the low-current draw from your end device will keep your power bank alive.\u003c\/p\u003e\n\u003cp\u003eYou plug one end of this into your power bank, the other end into your device, and there you have it - an easy, reliable mobile power source.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis is the assembled SMD version\u003c\/strong\u003e - ready to go with no soldering required - and sits a little more compact than the original kit version. If you would like the ability to change the resistor values or just fancy a simple soldering project, \u003ca href=\"\/ru\/products\/power-bank-keep-alive-based-on-555-timer-kit-form\"\u003eyou can grab the kit version here\u003c\/a\u003e. if you need something even more compact, check out \u003ca href=\"\/ru\/products\/power-bank-keepalive-usb-c\"\u003ethe USB-C version\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eYou can also \u003cstrong\u003e3D print a snap-together case\u003c\/strong\u003e for it, just \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4557971\"\u003edownload the file from Thingiverse\u003c\/a\u003e, grab some \u003ca href=\"\/ru\/collections\/3dqf\"\u003efilament\u003c\/a\u003e and away you go.\u003c\/p\u003e\n\u003ch2\u003ePower Bank Compatibility\u003c\/h2\u003e\n\u003cp\u003eWe've tested all \u003ca href=\"\/ru\/collections\/eplop\"\u003eEplop KeepAlives\u003c\/a\u003e with the \u003ca href=\"\/ru\/collections\/ansmann\"\u003eANSMANN power banks\u003c\/a\u003e we stock, and they work perfectly together.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eYour mileage may vary!\u003c\/strong\u003e We can't test every power bank out there, however Colin from Eplop has created these KeepAlives with values that should work with most.\u003c\/p\u003e\n\u003cp\u003eThe pass-through should work with all devices as the data lines are unaffected. With the resistor values chosen on its own it should not keep most power banks alive, but combined with a very low-power device, it should be enough to stop the power bank from powering off.\u003c\/p\u003e\n\u003ch2\u003eFrom the Designer\u003c\/h2\u003e\n\u003cp\u003e\u003cem\u003eWhen I'm working on small projects, I like to power them from a power bank or a similar item. Sometimes, the device draws such a small amount of power that it shuts down the power to the USB port as it thinks the device is off.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eThis device that I've designed will stay on by pulsing the power line to ensure that it doesn't shut down. It utilizes the 555 timer in an Astable circuit. With the configured resistors and capacitor, there is a 50% duty cycle which equates to roughly a 10mA draw with a pulse of approx 100mA. Combined with the draw of the device, this shall be enough to keep the power bank active. The data lines are directly connected and unaffected. - \u003ca href=\"https:\/\/x.com\/eplop\"\u003eColin Hickey\u003c\/a\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003ch2\u003eResources\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/docs.eplop.co.uk\/USBKeepAliveSMD.html\"\u003eKeepAlive (SMD) Documentation\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/docs.eplop.co.uk\/USBKeepAliveSMD.html#troubleshooting\"\u003eTroubleshooting\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.thingiverse.com\/thing:4557971\"\u003eThingiverse 3D Printed Case Design\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/discord.gg\/J7GnxDRaHj\"\u003eEplop Discord community\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003ePackage Contents\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e1x Assembled KeepAlive (SMD version)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eplop","offers":[{"title":"Default Title","offer_id":50847174492433,"sku":"106132","price":7.5,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0901\/6285\/6209\/files\/power-bank-keepalive-assembled-eplop-106132-71342479376769.jpg?v=1735207846","url":"https:\/\/abcd3032.myshopify.com\/ru\/products\/power-bank-keepalive-assembled","provider":"Tayyab Zak","version":"1.0","type":"link"}